INDUSTRIAL PLANT ENGINEERING || WITH ACCURATE ANSWERS 100%.
5 views 0 purchase
Module
INDUSTRIAL PLANT ENGINEERING
Institution
INDUSTRIAL PLANT ENGINEERING
Dynamic Head correct answers is the pressure head plus velocity head.
Carbon Steel Pipe correct answers a steel pipe that owes its properties chiefly to the carbon which it contains.
Galvanized Pipe correct answers a steel pipe coated with zinc to resist corrosion.
Wrought Pipe correct ans...
INDUSTRIAL PLANT ENGINEERING || WITH
ACCURATE ANSWERS 100%.
Dynamic Head correct answers is the pressure head plus velocity head.
Carbon Steel Pipe correct answers a steel pipe that owes its properties chiefly to the carbon
which it contains.
Galvanized Pipe correct answers a steel pipe coated with zinc to resist corrosion.
Wrought Pipe correct answers refers to both wrought steel and wrought iron. Wrought in this
sense means worked as in the process of forming furnace- welded pipe from skelp, or seamless
pipes form plates.
Fans correct answers used where low pressure from a few millimeters of 16 to 50 mmHg and
comparatively large volumes are required. They run at relatively low speed.
Net Positive Suction Head (NPSH) correct answers is the difference between the absolute
dynamic pressure of the liquid measured at the centerline of the pump and the saturation pressure
corresponding to the temperature of the liquid at the same point, all expressed in terms of head of
the fluid flowing.
Rotary Pump correct answers is a positive displacement pump consisting a fluid casing
containing gears, cams, screws, valves, plungers and similar elements actuated by rotation of the
drive shaft.
Fire Point correct answers temperature at which oil vapors will no longer flash but support
continuous flame.
Pour Point correct answers temperature at which oil will just flow under standard condition.
Viscosity correct answers in termed as absolute viscosity or a dynamic viscosity.
Check Valve correct answers a valve designed to allow a fluid to pass through in one direction
only.
Pipe correct answers a tube with around cross section conforming to the dimensional
requirements for nominal pipe size.
Blower correct answers is a machine to compress air or gas by centrifugal force to a final
pressure not exceeding 0.24 Mega Pascal Gage (MPa Gage). It is not water cooled (35 psi or 2.5
bars and below) as the aided expense of cooling system is not justified by the slight gain at these
pressures.
Relief Valve correct answers one designed to pen automatically to relief excess pressure.
, Pumps correct answers are devices to used to transfer fluid from region of low pressure to
another region of high pressure.
Expansion Loop correct answers a large radius bend in a pipeline to absorb longitudinal
expansion on the pipe line due to heat.
Black Pipe correct answers a steel pipe that has not been galvanized.
Manifold correct answers a fitting with a number of branches in line connecting to smaller pipes.
Used largely as a interchangeable terms with header.
Velocity head correct answers is the head required to produce the flow of water.
Compressor correct answers is a machine to compress air or gas to a fluid pressure of 0.24 MPa
Gage. They are usually water-cooled (above 35 psi or 2.5 bars)
Refrigerated Compressor correct answers compresses refrigerated vapor and causes it to flow in
the system.
Expansion Valve correct answers reduce d the pressure of the refrigerant so that low temperature
will be attained, regulates the flow of the refrigerant to the evaporator.
Evaporator correct answers the liquid portion of the refrigerant evaporates while absorbing heat
to the surroundings.
Steam correct answers a vapor into which water is converted when heated to its boiling point.
Fire Tube Boiler correct answers flue gas inside the tube and heated fluid outside the tube.
Y strainer correct answers its primary function is to protect the pump, normally strainers are
placed in the line at the inlet pumps, strainers for pump protection should not less than 40 mesh
and be made of bronze.
Pressure Gages correct answers are intended to determine the pump suction and discharge
pressure.
Bone Dry Weight (BDW) correct answers final constant weight reached by the a hygroscopic
substance after being dried out.
Gate Valve correct answers is intended for use as a stop valve or isolation valve. It gives the best
service where used in fully open or closed portion.
COD (Chemical Oxygen Demand) correct answers it is the chemical approach to measure the
amount of oxygen equivalent to the portion of organic matter that is susceptible to oxidation by
using a strong oxidant (potassium, dichromate and catalyst).
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller FullyFocus. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for £9.01. You're not tied to anything after your purchase.
