Welder - Study guides, Class notes & Summaries

Hoisting License (full) questions and solutions What is the purpose of the 520: C.M.R. 6:00? to establish rules and regulations for the safety of the public What type of equipment requires a hoisting license? equipment that has minimum capability of hoisting the load higher than 10' feet or equipment that has the capability of lifting loads greater than 500 pounds or equipment that has capacity of the becket exceeds 1/4 cubic yard What does A.S.M.E. stand for? American Society ...

Module 29105-15 Base Metal Preparation (19-20).fires Most work site ___________ related to welding operations are caused by cutting torches. strong The more carbon content steel has, the more ____________ the steel becomes. austenitic A term that refers to a type of metal stainless steel group, which is most often encountered by welders. chromium Common-grade stainless steels normally contain at least 11 percent _________________. classified Grain structures are the way ...

To measure the strength of a welded joint what mechanical test would you prescribe? a) A transverse weld tension test. b) A charpy test. c) A CTOD test. d) An all weld metal tension test. e) A side bend test. - a) A transverse weld tension test. Select the cutting process that would provide the narrowest heat affected zone when cutting 12.5 mm (0.5 in) thick carbon steel. a) Oxy-acetylene cutting. b) Air-carbon arc cutting. c) Oxy-propane cutting. d) Plasma arc cutting. e) Laser beam...

Defects on gas piping or fittings shall be _____.(A) repaired(B) replaced or repaired and retested(C) repaired by a certified welder(D) ignored, as the operating pressure is much less than the air test. - Answer B. Fitting shall be replaced or repaired and retested. UMC Section 1316.4.3 Every absorption refrigerating system supported from the ground shall rest on a concrete slab extending not less than _____ the adjoining ground level.(A) 3 inches below(B) 3 inches above (C) 6 inches below(...

What is the suggested filler metal classification for welding ASTM A131 Grade DH32 steel with GMAW ? - Answer-ER70S-X When fillet welding a 3/8 inch stud in the flat position with an E7018 electrode, what diameter electrode must be used? - Answer-3/16 inch How long does welder certification last per AWS D1.1? - Answer-indefinitely, unless not engaged in the process for more than 6 months at a time With a single electrode for SAW what is the maximum size single pass fillet weld that can be ...

To measure the strength of a welded joint what mechanical test would you prescribe? a) A transverse weld tension test. b) A charpy test. c) A CTOD test. d) An all weld metal tension test. e) A side bend test. - correct answer a) A transverse weld tension test. Select the cutting process that would provide the narrowest heat affected zone when cutting 12.5 mm (0.5 in) thick carbon steel. a) Oxy-acetylene cutting. b) Air-carbon arc cutting. c) Oxy-propane cutting. d) Plasma ...

CWB Level 2 Closed Book Questions and Answers 100% Correct CWB Level 2 Closed Book Questions and Answers 100% Correct CWB Level 2 Closed Book Questions and Answers 100% Correct To measure the strength of a welded joint what mechanical test would you prescribe? a) A transverse weld tension test. b) A charpy test. c) A CTOD test. d) An all weld metal tension test. e) A side bend test. - ANSWER-a) A transverse weld tension test. Select the cutting process that would provide the...

The minimum blowdown for a spring loaded safety valve shall be of what percent of set pressure? Correct Answer 10% How is the main steam pressure gages tested? Correct Answer With an inspectors gage Who is in charge of the code for any plumbing installations? Correct Answer The nyc plumbing code When will anchorage or guides be inspected? Correct Answer Annually How many brass washout plugs does a miniature boiler have? Correct Answer 3 brass washout plugs, 1" in size How often i...

Nyc high pressure boiler license Exam Questions with Correct Answers The minimum blowdown for a spring loaded safety valve shall be of what percent of set pressure? - Answer-10% How is the main steam pressure gages tested? - Answer-With an inspectors gage Who is in charge of the code for any plumbing installations? - Answer-The nyc plumbing code When will anchorage or guides be inspected? - Answer-Annually How many brass washout plugs does a miniature boiler have? - Answer-3 brass wa...

Nyc high pressure boiler license exam with question and answers latest update The minimum blowdown for a spring loaded safety valve shall be of what percent of set pressure? - ANSWER>>10% How is the main steam pressure gages tested? - ANSWER>>With an inspectors gage Who is in charge of the code for any plumbing installations? - ANSWER>>The nyc plumbing code When will anchorage or guides be inspected? - ANSWER>>Annually How many brass washout plugs does a miniature b...

2024 AG Mechanics CDE: MIG Welder Parts Questions & Answers 100% Accurate2024 AG Mechanics CDE: MIG Welder Parts Questions & Answers 100% Accurate2024 AG Mechanics CDE: MIG Welder Parts Questions & Answers 100% AccurateContact Tip - ANSWERTransfers the welding current to the wire as it passes through the bore, hence creating the arc. Drive Roll - ANSWERThe Drive roll feeds the wire smoothly from the wire spool into the gun cable. Electrode Holder - ANSWERHolds an electrode in a position th...

NEIEP 800 final review Exam Questions and Answers 100% Verified 2024 The total weight of your elevator (force) is 8100 lbs. and its plunger area is 50 square inches. What is the system pressure? - answer162 psi Refer to the NEIEP Moving Walk Final Layout. What is the correct wellway-to-wellway distance? - answer134' 11" Electrolysis is caused by which of the following? - answerStray current corrosion and Galvanic corrosion BOTH ARE CORRECT When using wire rope, the diameter of the shea...