MK1 SWE P.1(Jen's notes)| 250 QUESTIONS| WITH COMPLETE SOLUTIONS
5 keer bekeken 0 keer verkocht
Vak
MK1
Instelling
Liberty University
A _____ or _____ equivalent shall be submitted for all vessels _____ ft or greater annually covering a 12 month period ending Dec. 31st. correct answer: Cutter Engineering Report (CG 4874), CM+ equivalent, 65
Section VI of the cutter engineering report correct answer: For general remarks not c...
mk1 swe p1jens notes| 250 questions| with complete solutions
Geschreven voor
Liberty University
MK1
Alle documenten voor dit vak (16)
Verkoper
Volgen
Classroom
Ontvangen beoordelingen
Voorbeeld van de inhoud
MK1 SWE P.1(Jen's notes)| 250 QUESTIONS| WITH
COMPLETE SOLUTIONS
A _____ or _____ equivalent shall be submitted for all vessels _____ ft or greater annually covering a 12 month period ending Dec. 31st. correct answer: Cutter Engineering Report (CG 4874), CM+ equivalent, 65
Section VI of the cutter engineering report correct answer: For general remarks not covered elsewhere in the report
Who develops and publishes guidance for the preparation, submittal and processing of SSMR's correct answer: MLC's
Casualties affecting a secondary mission shall always have a casualty category of _____? correct answer: Category 2
A statement of work specifies in clear understandable terms the work to be done by a _____? correct answer: Contractor
A detailed Boat Inspection Report (CG-3022) shall be submitted
on _____ correct answer: All boats less than 65 feet in length
Group/sector and district commands shall schedule a detailed boat inspection of each boat at an interval not to exceed _____ correct answer: 1 year between inspections
A bright spot found on each end of a broken piston ring indicates correct answer: Insufficient gap clearance A _____ is installed on the tank to prevent the pump motor and solenoid valve from becoming energized in the event the condensate tank water is low correct answer: Float switch
The distance the driving bore of a hub is out of parallel with the shaft center line correct answer: Bore run out
Any eccentricity or perpendicularity errors mush be accounted for in _____ correct answer: The alignment process
How do you check the bore alignment correct answer: Take measurements of the diameter gap at four equally spaced points on the flanges diameter
To check angular alignment correct answer: Use a feeler gauge at four equal spaces
Specific authorization from the _____ is required before removal of an inspection plate, connection, fitting or cover which permits access to the gear casing correct answer: Engineering Officer
At the first sign of emulsion _____ and _____ correct answer: Stop the plant, change the oil
All cutters 65 feet and longer are required to maintain _____ correct answer: A machinery history file
The amount of deflection of a crankshaft may be determined by the use of _____ correct answer: A strain gauge The _____ reports identifying info for all navy reporting system (NRS) messages. Signifies beginning of formatted information. Also the message type and message originator correct answer: MSGID
The _____ reports a units present location and effective date-
time correct answer: POSIT
The _____ reports the requirement for outside assistance correct answer: ASSIST
SSMR Priority 1 correct answer: Immediate
SSMR Priority 2 correct answer: Early accomplishment, 6 months-2 years
SSMR Priority 3 correct answer: To be accomplished as normal
back log up to 5 years
Reasons for SSMR change recommendations correct answer: -
Safety
-Lack of personnel
-Interferences with wire, windows, doors, plumbing, etc
-Missing drawing or drawing parts
_____ contains data that is used to preserve the continuity of operational history of a piece of equipment correct answer: Machinery history
Who determines what procedures are used to make a change to the SSMR correct answer: Sector/Group SOP's As a supervisor, during the planning stage, you should _____ correct answer: Check on all materials like flexible hoses, gauges and all consumable materials before you start working on any job
As a supervisor, while inspecting the job you should _____ correct answer: Carefully consider the capabilities and experience of your personnel, then assign work
The _____ is responsible for ensuring all post overhaul tests, inspection and break-in procedures are conducted correct answer: Supervisor
Characterized by improper functioning of a torsion vibration dampner correct answer: Bent or broken crankshaft
Characterized by the presence of fine abrasives in lubricants correct answer: Bearing wear causing looseness without apparent surface degradation
If you have an OWS that doesn't discharge oil, it could be the _____ or the _____ correct answer: Probe amplifier relay, oil sensing probe
All of the following information may be contained in the ID block of a schematic except for the _____
a. Title b. Platform c. Sheet index d. Drawing number correct answer: C. Sheet index
Voordelen van het kopen van samenvattingen bij Stuvia op een rij:
Verzekerd van kwaliteit door reviews
Stuvia-klanten hebben meer dan 700.000 samenvattingen beoordeeld. Zo weet je zeker dat je de beste documenten koopt!
Snel en makkelijk kopen
Je betaalt supersnel en eenmalig met iDeal, creditcard of Stuvia-tegoed voor de samenvatting. Zonder lidmaatschap.
Focus op de essentie
Samenvattingen worden geschreven voor en door anderen. Daarom zijn de samenvattingen altijd betrouwbaar en actueel. Zo kom je snel tot de kern!
Veelgestelde vragen
Wat krijg ik als ik dit document koop?
Je krijgt een PDF, die direct beschikbaar is na je aankoop. Het gekochte document is altijd, overal en oneindig toegankelijk via je profiel.
Tevredenheidsgarantie: hoe werkt dat?
Onze tevredenheidsgarantie zorgt ervoor dat je altijd een studiedocument vindt dat goed bij je past. Je vult een formulier in en onze klantenservice regelt de rest.
Van wie koop ik deze samenvatting?
Stuvia is een marktplaats, je koop dit document dus niet van ons, maar van verkoper Classroom. Stuvia faciliteert de betaling aan de verkoper.
Zit ik meteen vast aan een abonnement?
Nee, je koopt alleen deze samenvatting voor €14,70. Je zit daarna nergens aan vast.
