100% tevredenheidsgarantie Direct beschikbaar na betaling Zowel online als in PDF Je zit nergens aan vast
logo-home
NCCER MILLWRIGHT PRACTICE EXAM 2 QUESTIONS AND ANSWERS 100% ACCURATE €10,74   In winkelwagen

Tentamen (uitwerkingen)

NCCER MILLWRIGHT PRACTICE EXAM 2 QUESTIONS AND ANSWERS 100% ACCURATE

 287 keer bekeken  1 keer verkocht
  • Vak
  • NCCER MILLWRIGHT
  • Instelling
  • NCCER MILLWRIGHT

NCCER MILLWRIGHT PRACTICE EXAM 2 QUESTIONS AND ANSWERS 100% ACCURATENCCER MILLWRIGHT PRACTICE EXAM 2 QUESTIONS AND ANSWERS 100% ACCURATENCCER MILLWRIGHT PRACTICE EXAM 2 QUESTIONS AND ANSWERS 100% ACCURATE unusual - ANSWER-If the seal was not properly aligned or there is excessive wear in some bear...

[Meer zien]

Voorbeeld 2 van de 9  pagina's

  • 8 september 2023
  • 9
  • 2023/2024
  • Tentamen (uitwerkingen)
  • Vragen en antwoorden
  • NCCER MILLWRIGHT
  • NCCER MILLWRIGHT
avatar-seller
NCCER MILLWRIGHT PRACTICE EXAM 2 QUESTIONS AND ANSWERS 100% ACCURATE
unusual - ANSWER-If the seal was not properly aligned or there is excessive wear in some bearing or shaft,_______ wear tracks will be the indicator
sharpened brass putty knife - ANSWER-For removing hard to remove gasket materials found on sealing surfaces, ______ is recommended
Conducted on the job - ANSWER-Apprenticeship training is_______
distance - ANSWER-Charting alignment on a graph requires a chart that is divided into thousandths of an inch vertically for the indicator readings and into whole inches horizontally for the__________
hidden - ANSWER-The orthographic drawing may contain a dashed or _______ line
Radiation - ANSWER-In order to shoot through a test object and project an image onto a detector or a sheet of film, radiography uses a source of penetrating called _______
*scribe circles
*transfer measurements *compare distances <measure angles - ANSWER-Which of the following task would you not perform with dividers?
10% - ANSWER-The over speed trip device is actuated when the turbine reaches a predetermined limit usually _________% above normal full-load speed
high - ANSWER-Positive results in an offset measurement mean that the MTBM is _____ or on the 3-o'clock side.
offset misalignment - ANSWER-The coupling gap is set, and then the ______ is measured
pressure - ANSWER-In a hydraulic system, movement depends on_____
furniture or utility items - ANSWER-Fractional dimensions are used on objects such as _______ or ______ elimination - ANSWER-If the cause of the problem is not immediately understood, the process of________is often the procedure of choice
3/16 - ANSWER-When applying sealant to the sealing gland flanges, keep the sealant away from the inside edges of the flange by at least_______ inch
Transducer - ANSWER-A stroboscope is triggered by a_______
thread - ANSWER-The pitch of threaded fasteners is measured with a ________gauge
Surface cracks - ANSWER-Liquid penetrant highlights flaws and reveals________
die - ANSWER-A tool used to cut external threats on s bolt or rod is called a ______
special processes - ANSWER-A bill of materials may include info on _______ and other
reference information
surface speed - ANSWER-Engaged gears always have the same _____
general arrangement - ANSWER-Elevation of equipment is usually found in the_____
Vibrations - ANSWER-Inspect the pulleys, rollers, and idlers for unevenness or______
15-20 degree angle - ANSWER-When cutting thin steel with Oxyfuel fuel cutting equipment, hold the torch so that the tip is pointing in the direction the torch is traveling at a _____ angle
Grease......... - ANSWER-Labby seals work BEST with materials such as_____
Friction - ANSWER-Lubrication is the application of any substance that reduces________
Driver coupling jig - ANSWER-When the dial indicator is mounted on the complex reverse driven coupling jig , the indicator is registered on the____
In racks - ANSWER-Pipe should be stored_____
Single deep groove radial - ANSWER-The most common type of ball bearing is a _____
bearing
split - ANSWER-Couplings that are installed after the driver and driven shafts have been aligned and the equipment has been fastened into position are ________ couplings

Voordelen van het kopen van samenvattingen bij Stuvia op een rij:

Verzekerd van kwaliteit door reviews

Verzekerd van kwaliteit door reviews

Stuvia-klanten hebben meer dan 700.000 samenvattingen beoordeeld. Zo weet je zeker dat je de beste documenten koopt!

Snel en makkelijk kopen

Snel en makkelijk kopen

Je betaalt supersnel en eenmalig met iDeal, creditcard of Stuvia-tegoed voor de samenvatting. Zonder lidmaatschap.

Focus op de essentie

Focus op de essentie

Samenvattingen worden geschreven voor en door anderen. Daarom zijn de samenvattingen altijd betrouwbaar en actueel. Zo kom je snel tot de kern!

Veelgestelde vragen

Wat krijg ik als ik dit document koop?

Je krijgt een PDF, die direct beschikbaar is na je aankoop. Het gekochte document is altijd, overal en oneindig toegankelijk via je profiel.

Tevredenheidsgarantie: hoe werkt dat?

Onze tevredenheidsgarantie zorgt ervoor dat je altijd een studiedocument vindt dat goed bij je past. Je vult een formulier in en onze klantenservice regelt de rest.

Van wie koop ik deze samenvatting?

Stuvia is een marktplaats, je koop dit document dus niet van ons, maar van verkoper NursingTutor1. Stuvia faciliteert de betaling aan de verkoper.

Zit ik meteen vast aan een abonnement?

Nee, je koopt alleen deze samenvatting voor €10,74. Je zit daarna nergens aan vast.

Is Stuvia te vertrouwen?

4,6 sterren op Google & Trustpilot (+1000 reviews)

Afgelopen 30 dagen zijn er 78252 samenvattingen verkocht

Opgericht in 2010, al 14 jaar dé plek om samenvattingen te kopen

Start met verkopen
€10,74  1x  verkocht
  • (0)
  Kopen