Tentamen (uitwerkingen)
ASME B31.3 PROCESS PIPING CODE EXAM
- Vak
- Instelling
ASME B31.3 PROCESS PIPING CODE EXAM ....
[Meer zien]Voorbeeld 3 van de 16 pagina's
Voorbeeld 3 van de 16 pagina's
In winkelwagen
In winkelwagen
gesponsord bericht van onze partner
Verkoper
Volgen
Mirror
Ontvangen beoordelingen
Voorbeeld van de inhoud
ASME B31.3 PROCESS PIPING CODE EXAM2024-2025
The requirements of the most recent edition of ASME Code B31.3, and any future
addenda: - ANSWER Are not retroactive, and all equipment installed in older
editions does not need to be upgraded.
Clauses in the B31 code are not always numbered consecutively. Such
discontinuities result from ANSWER Insofar as is practical, all code parts should
follow a common outline.
Who is responsible for establishing which code section applies to plumbing
installations, such as B31.1, B31.3, and so on? - ANSWER Owner.
Who is ultimately responsible for ensuring ASME B31.3 compliance? - ANSWER
Owner.
ASME B31.3 is intended to establish forth engineering specifications deemed
required for ________. Pipeline installations should be designed and built safely.
The ASME code is not designed to apply to plumbing. - ANSWER That has been
put into service.
Material compatibility with the service, as well as dangers resulting from fluid
instability: - ANSWER Are outside the scope of ASME B31.3.
ASME B31.3 covers pipework for all fluids except: - ANSWER Tubes for fired
heaters, plumbing, and storm drains.
,A prep-laced filler metal that is fully melted into the root of a welded connection
and becomes part of the weld is called: - ANSWER A consumable insert.
Define "face of weld". - ANSWER It is the exposed surface of a weld on the side
from whence it was created.
A category _____ fluid is neither flammable, harmless, or harmful to human tissue,
has a gage pressure of no more than 150 psi, and has a design temperature range of
-20 degrees to 366 degrees Fahrenheit. - Answer D.
A category ______ fluid has the potential for significant personnel exposure and
where a single exposure to a very small quantity of toxic fluid, caused by leakage,
can cause serious irreversible harm to people on breathing or bodily contact, even
when prompt restorative measures are taken. - ANSWER M
A fillet weld that is equal to the thickness of the thinner element connected is
called: - ANSWER A full fillet weld.
The heating and holding of metal to a suitable temperature and then cooling at a
suitable rate for such purposes as: reducing hardness, improving machinability,
facilitating cold working, producing a desired microstructure, or obtaining desired
mechanical, physical, or other properties is known as: - ANSWER Annealing.
A piping joint that provides mechanical strength through threaded, grooved, rolled,
flared, or flanged pipe ends, or bolts, pins, toggles, or rings, and leak resistance
through threads and compounds, gaskets, rolled ends, caulking, or machined and
mated surfaces is known as: - ANSWER: Mechanical joint
The word NPS 6 refers to: - A pipe with an outer diameter of 6.625 inches.
A pipe made by piercing a billet and then rolling, drawing, or both is called a: -
ANSWER Seamless pipe
, What is a root opening? - ANSWER It is the gap between the parts that will be
united by welding at the joint's root.
A weld designed primarily to ensure junction tightness against leaking in metallic
pipework is known as: - Answer: Seal weld
A tack weld is created to keep the components of a weld in perfect alignment until
the final welds are made.
The intersection between the face of the weld and the base metal is known as the
"toe of the weld."
The pressure in a piping system that is the pressure at the most severe condition of
coincident internal or external pressure and temperature (minimum or maximum)
expected during service (except for allowances for occasional variations in
pressure, temperature, or both, above operating levels, which are characteristics of
certain services) is known as: - ANSWER: Design pressure
Piping that is not protected by a pressure relieving device or that can be detached
from a pressure relieving device must be constructed for at least the following: -
Maximum pressure that can be created.
What happens if a piping system containing gas or vapor is allowed to cool
significantly? - ANSWER The pressure in the pipe system may drop enough to
create an internal vacuum.
Voordelen van het kopen van samenvattingen bij Stuvia op een rij:
Verzekerd van kwaliteit door reviews
Stuvia-klanten hebben meer dan 700.000 samenvattingen beoordeeld. Zo weet je zeker dat je de beste documenten koopt!
Snel en makkelijk kopen
Je betaalt supersnel en eenmalig met iDeal, creditcard of Stuvia-tegoed voor de samenvatting. Zonder lidmaatschap.
Focus op de essentie
Samenvattingen worden geschreven voor en door anderen. Daarom zijn de samenvattingen altijd betrouwbaar en actueel. Zo kom je snel tot de kern!
Veelgestelde vragen
Wat krijg ik als ik dit document koop?
Je krijgt een PDF, die direct beschikbaar is na je aankoop. Het gekochte document is altijd, overal en oneindig toegankelijk via je profiel.
Tevredenheidsgarantie: hoe werkt dat?
Onze tevredenheidsgarantie zorgt ervoor dat je altijd een studiedocument vindt dat goed bij je past. Je vult een formulier in en onze klantenservice regelt de rest.
Van wie koop ik deze samenvatting?
Stuvia is een marktplaats, je koop dit document dus niet van ons, maar van verkoper Mirror. Stuvia faciliteert de betaling aan de verkoper.
Zit ik meteen vast aan een abonnement?
Nee, je koopt alleen deze samenvatting voor €10,59. Je zit daarna nergens aan vast.
Is Stuvia te vertrouwen?
4,6 sterren op Google & Trustpilot (+1000 reviews)
Afgelopen 30 dagen zijn er 72841 samenvattingen verkocht
Opgericht in 2010, al 14 jaar dé plek om samenvattingen te kopen