Tentamen (uitwerkingen)
Woodworking and Customizing Exam Graded A+
- Vak
- Instelling
Woodworking and Customizing Exam Graded A+
[Meer zien]Voorbeeld 2 van de 11 pagina's
Voorbeeld 2 van de 11 pagina's
In winkelwagen
In winkelwagen
gesponsord bericht van onze partner
Verkoper
Volgen
CLOUND
Ontvangen beoordelingen
Voorbeeld van de inhoud
Woodworking and Customizing Exam Graded A+1 1/16in - 1in - ANSWER-Which sizes of chisels and gouges are mostly used to carve
gunstocks?
1 hour - ANSWER-When using checkering-pattern decals, how long should you wait
after the decal has been attached to the stock before starting to cut the lines?
1/32 - 1/16 inches - ANSWER-When inletting a gunstock with glass bedding, how much
clearance should be left in the barrel channel and behind the recoil lug?
12 - 15 degrees - ANSWER-To what angle should the cutting edge of a straight skew
chisel be ground on both sides of the blade?
14 - ANSWER-The pull on most American firearms is about ------, which is about right
for the average male.
18 and 24 - ANSWER-In general, checkering for hunting rifles should be between
________ liner per inch
20 - ANSWER-Which of the following lpi patterns is not considered "decorative
checkering"?
3/8 inch. - ANSWER-What is the recommended diameter of wooden dowels used to
repair broken stocks at the pistol grip?
60 cutter - ANSWER-When cutting the basic outline for a carving pattern, what type of
veining tool should be used?
A birch dowel coated with epoxy inserted through the break. - ANSWER-When repairing
a break at the pistol grip on a rifle stock, what should be used to strengthen the repair
besides epoxy?
A checkering cradle - ANSWER-What is the best device to hold a gunstock during the
checkering process?
A dent in wood is merely a compression of [wood fibers], and the application of [steam]
to the area will cause the fibers to [swell] and rise to the surface of the wood. -
ANSWER-A dent in wood is merely a compression of ----, and the application of ----- to
the area will cause the fibers to ------- and rise to the surface of the wood.
A metal plate that fits on the butt of a gunstock to protect the edges but is hollow in the
center portion of the plate. This inside area usually shows checkered wood. - ANSWER-
Which of the following is a good description of a skeletonized buttplate?
, A skeletonized grip cap. - ANSWER-One type of gunstock furniture that matches a
skeletonized buttplate is:
A soft-bristle toothbrush. - ANSWER-What tool is normally used to apply gunstock finish
to a checkered area on the gunstock?
After the barrel, receiver and trigger guard have been inlet. - ANSWER-When are heel
and comb cut?
All metal parts should be removed from the gunstock. - ANSWER-What should be done
before any finish is removed from a gunstock under repair?
All the above - ANSWER-To begin the design of a rifle stock, what are some of the
factors you must consider?
American walnut - ANSWER-The traditional stock wood today is still
American, English, and French. - ANSWER-What are the three types of basic
checkering patterns used on modern firearms?
An extension of the buttstock, attached to the butt of the stock to extend trigger pull
and/or cushion recoil. - ANSWER-Which of the following definitions describes a recoil
pad?
Ask for a second person to assist in the procedure. - ANSWER-
B-square Co - ANSWER-An excellent swivel installation tool kit is available from
____________. This kit enables sling swivels to be installed quickly on any stock
without risk of damage.
b. To bring the sight to eye level. - ANSWER-Why is some drop at heel necessary in all
gunstocks?
Bedding - ANSWER-as applied to gunstocks, refers to the methods used to mate the
metal (barrel and action) to the wood.
bedding - ANSWER-The ------ of the barrel and receiver is very important to ensure
good accuracy and prevent damage to the stock under the rifle recoil.
Before the shaping and inletting is started - ANSWER-When inletting or shaping a
gunstock, perform all metal work (bluing, machining, etc.):
belt/disk sander - ANSWER-A ------- is a favorite tool in gun shops to smooth down
replacement pieces for gunstock.
Blocking chisel - ANSWER-One of these items is not good for repairing a stock:
Voordelen van het kopen van samenvattingen bij Stuvia op een rij:
Verzekerd van kwaliteit door reviews
Stuvia-klanten hebben meer dan 700.000 samenvattingen beoordeeld. Zo weet je zeker dat je de beste documenten koopt!
Snel en makkelijk kopen
Je betaalt supersnel en eenmalig met iDeal, creditcard of Stuvia-tegoed voor de samenvatting. Zonder lidmaatschap.
Focus op de essentie
Samenvattingen worden geschreven voor en door anderen. Daarom zijn de samenvattingen altijd betrouwbaar en actueel. Zo kom je snel tot de kern!
Veelgestelde vragen
Wat krijg ik als ik dit document koop?
Je krijgt een PDF, die direct beschikbaar is na je aankoop. Het gekochte document is altijd, overal en oneindig toegankelijk via je profiel.
Tevredenheidsgarantie: hoe werkt dat?
Onze tevredenheidsgarantie zorgt ervoor dat je altijd een studiedocument vindt dat goed bij je past. Je vult een formulier in en onze klantenservice regelt de rest.
Van wie koop ik deze samenvatting?
Stuvia is een marktplaats, je koop dit document dus niet van ons, maar van verkoper CLOUND. Stuvia faciliteert de betaling aan de verkoper.
Zit ik meteen vast aan een abonnement?
Nee, je koopt alleen deze samenvatting voor €11,29. Je zit daarna nergens aan vast.
Is Stuvia te vertrouwen?
4,6 sterren op Google & Trustpilot (+1000 reviews)
Afgelopen 30 dagen zijn er 67096 samenvattingen verkocht
Opgericht in 2010, al 14 jaar dé plek om samenvattingen te kopen