Tentamen (uitwerkingen)
(SDI) FTT 221-9445 Sights, Optics, and Accuracy
- Vak
- Instelling
(SDI) FTT 221-9445 Sights, Optics, and Accuracy
[Meer zien]Voorbeeld 2 van de 7 pagina's
Voorbeeld 2 van de 7 pagina's
In winkelwagen
In winkelwagen
gesponsord bericht van onze partner
Verkoper
Volgen
CLOUND
Ontvangen beoordelingen
Voorbeeld van de inhoud
(SDI) FTT 221-9445 Sights, Optics, andAccuracy
\frac{M (gr)}{7000 ∙ D(in)^2} - ANSWER-Which of the following is the equation that is
used to calculate sectional density?
12 - ANSWER-Nathan Foster recommends ----- shots for the initial break in of a barrel.
35 in-lb - ANSWER-Torque the action screws on a Tika T3 to
57 - ANSWER-A radian is approximately how many degrees
a rigid method - ANSWER-Mock bedding utilizes -------- for temporary testing.
a. 1/60 of a degree - ANSWER-Speaking in angular measurement terms, a "minute" is:
a. 8-40 - ANSWER-Heavier recoil guns will use ______ mounting screw holes.
a. Bead front sight; Notched open rear sight - ANSWER-According to the text, the most
common metallic sights are:
a. Between .2mm and .5mm - ANSWER-How much gap needs to exist between a
Mauser magazine box and the floorplate?
a. Cast - ANSWER-According to the Article, "Diagnosing Hunting Rifle Accuracy Part I",
the author speaks about his prowess in which type of bullet design used with the RCBS
Cowboy dies?
a. Cut back a spring and stretch into position. - ANSWER-The Howa HACT trigger can
be modified by ________, although it is a very risky procedure.
a. Drop test the rifle
b. Fast-cycle the action when the rifle is assembled
c. Test the safety
****d. All the above - ANSWER-Which of the following tests must be done to the rifle
after trigger modifications have taken place?
a. Ensure a perfect alignment between two rings. - ANSWER-The bar lapping
procedure is meant to:
a. Heat ruining the temper of trigger springs
b. Filing the geometry of triggers at an unsafe angle
c. Modifying triggers to less than 1lb
, ****d. All the above - ANSWER-The author highly warns against a DIY trigger job
because:
a. Improper use of piloted crowning tools - ANSWER-Circumferential burrs that occur
near the tip of the bore of a rifle were most likely caused by:
a. Lateral cant
b. Eye relief
c. Longitudinal cant
d. Ring alignment - ANSWER-When setting up a scope, consider which of the following
factors (choose all that apply):
a. Leupold/Redfield - ANSWER-Which type of mount includes windage adjustments?
a. Light copper fouling that is easily removed indicates near break-in, and harsh
abrasive polishing should be avoided. - ANSWER-When removing copper from the
bore, you should observe the ease with which the copper comes free. Choose the
correct statement below:
a. Maurice of Orange - ANSWER-The first army commander that ordered sights to be
installed on guns was:
a. On most rifles, this method requires reapplication each time the rifle is disassembled
for detailed maintenance. - ANSWER-One major disadvantage of Mr. Walker's "glue
and screw" method is:
a. Open up bore dimensions at the chamber end of the rifle
b. Smooth the bore - ANSWER-Which of the following is a possible outcome of fire
lapping (choose all that apply)?
a. preliminary testing or semi-permanent bedding. - ANSWER-The "glue and screw"
technique is suitable for:
a. Rosin - ANSWER-Which substance is used to prevent scope rings to slip against
each other during shooting?
a. Ruger No. 1 - ANSWER-Mr. Foster's instructions for setting up a Tika T3 rifle for
testing and field-usage can also be applied to all of the following platforms except?
a. Square from the top of the overarm. - ANSWER-On a Forster jig, it is possible to fit
non-square based actions by means of a:
a. Stock inlet is too low
b. Improper assembly - ANSWER-What are the ways a magazine box can "pinch" the
action of a rifle?
Dit zijn jouw voordelen als je samenvattingen koopt bij Stuvia:
Bewezen kwaliteit door reviews
Studenten hebben al meer dan 850.000 samenvattingen beoordeeld. Zo weet jij zeker dat je de beste keuze maakt!
In een paar klikken geregeld
Geen gedoe — betaal gewoon eenmalig met iDeal, creditcard of je Stuvia-tegoed en je bent klaar. Geen abonnement nodig.
Direct to-the-point
Studenten maken samenvattingen voor studenten. Dat betekent: actuele inhoud waar jij écht wat aan hebt. Geen overbodige details!
Veelgestelde vragen
Wat krijg ik als ik dit document koop?
Je krijgt een PDF, die direct beschikbaar is na je aankoop. Het gekochte document is altijd, overal en oneindig toegankelijk via je profiel.
Tevredenheidsgarantie: hoe werkt dat?
Onze tevredenheidsgarantie zorgt ervoor dat je altijd een studiedocument vindt dat goed bij je past. Je vult een formulier in en onze klantenservice regelt de rest.
Van wie koop ik deze samenvatting?
Stuvia is een marktplaats, je koop dit document dus niet van ons, maar van verkoper CLOUND. Stuvia faciliteert de betaling aan de verkoper.
Zit ik meteen vast aan een abonnement?
Nee, je koopt alleen deze samenvatting voor €11,27. Je zit daarna nergens aan vast.
Is Stuvia te vertrouwen?
4,6 sterren op Google & Trustpilot (+1000 reviews)
Afgelopen 30 dagen zijn er 69052 samenvattingen verkocht
Opgericht in 2010, al 15 jaar dé plek om samenvattingen te kopen
Laatst bekeken door jou
