1) When is the BEST time to document each loop check for commissioning ? A. Prior to the start of inspection
B. When all test and inspection activities are complete
C. When updating information on a daily basis
D. At the time each test is completed - ANS D. At the time each test is complet...
,1) When is the BEST time to document each loop check for commissioning ? A. Prior to the start
of inspection
B. When all test and inspection activities are complete
C. When updating information on a daily basis
D. At the time each test is completed - ANS D. At the time each test is completed (INST
LVL4)(12410-16/ Section 3.2.0)
2) Teflon paste must not be used on :
A. Nitrogen service
B. Natural gas service
ck
C. Water service
D. Oxygen service - ANS D. Oxygen service (INST LVL 1 )(12109-14/Section 2.1.1)
3) A 24VDC power supply is not working . With your multimeter you verify no DC voltage . On
the 120VAC input you measure 120V between hot and ground , and 72V between hot and
B. Lost the hot
C. Lost the neutral
D. Lost the fuse - ANS C. Lost the neutral
lo
neutral . What is the most likely cause of this ?
A. Lost the ground
yc
4) Gain increase when tube :
A. Back bends are made
B. Bend radius increases
C. Size decreases
ud
D. Long radius elbows are used - ANS B. Bend radius increases (INST LVL 2)(12302-15
section 2.1.1)
5) A temperature measuring device that produces a voltage as the temperature changes is a /
an :
A. RTD
st
B. Thermistor
C. Thermometer
D. Thermocouple - ANS D. Thermocouple (INST LVL 2) (12110-15 section 1.2.2)
6) A pressure piping code is found in :
A. ANSI B 31.1
B. NEC 690 .
C. OSHA1910 .
D. ISA S 5.1 - ANS A. ANSI B 31.1
7) When marking tubing for cutting , the preferred method is
,A. Scribe a mark into the tube with a sharp object .
B. Mark the tube with a grease pencil
C. Mark the tube with a felt tip pen
D. Mark the tube with a crayon - ANS C. Mark the tube with a felt tip pen
8) An example of direct measurement indicator is a :
A. Pressure gauge
B. Bulb thermometer
C. Sight glass
D. Flowmeter - ANS C. Sight glass
9) On the image , how many hand valves are installed on Tank 1201C
ck
A. 1
B. 2
C. 3
D. 4 - ANS C. 3
B. Stimulate an input
C. Verify that there is a problem
lo
10) What is the first step in troubleshooting a problem in a system ?
A. Turn off power to the instrument
D. Stimulate an output - ANS C. Verify that there is a problem
yc
11) Where can the appropriate elevation of an instrument be found ?
A. Location drawing
B. P & ID
C. Flow diagram
ud
D. Loop drawing - ANS A. Location drawing
12) Chemical cleaning of tubing attached to instruments may cause damage to sensor
A. Electronics
B. Paint
C. Elements
st
D. Bolts - ANS C. Elements
13) When making 90 - degree tubing bend , allowance for springback should be : A. 6 to 8
degrees
B. 4-5 degrees
C. 1 to 3 degrees
D. 0 degrees - ANS C. 1 to 3 degrees
14) Cable shields should be connected to the :
A. Signal ground reference point
B. Ground at each accessible location
, C. First accessible grounding electrode
D. Raceway or cable tray in which the cable is routed - ANS B. Ground at each accessible
location
15) An employee de energizes a piece of equipment by removing the power plug from the outlet
. If the employee continues to hold on to the power plug once removed , this employee is said to
have what type of control over the energy potential ?
A. Isolation control
B. Lockout tagout
C. Exclusive control
D. Remote control - ANS C. Exclusive control
ck
16) A compressor keeps blowing a PSV for troubleshooting a technician should start looking at
A. Power switch setting
B. Pressure switch deadband
C. Level switch setting
D. Float swich deadband - ANS B. Pressure switch deadband
gas is labeled as
A. A
B. B
lo
17) In the figure provided the pipe line that carries working process fluid such as steam water or
yc
C. C
D. D - ANS A. A
18) A heat reactive dryer is producing damp instrument air what could be a simple fix
A. Replace desiccant
ud
B. Change to a different desiccant
C. Adjust the cycle time
D. Add a second set of dryers - ANS C. Adjust the cycle time
19) Type J thermocouple extension wire is
A. White & red
st
B. Yellow & red
C. Blue & red
D. Green & red - ANS A. White & red
20) Which of the following gases should be used to purge tubing and pipe after cleaning
A. argon
B. Air
C. Nitrogen
D. helium - ANS C. Nitrogen
21) When pressure testing , the required documentation includes :
Voordelen van het kopen van samenvattingen bij Stuvia op een rij:
Verzekerd van kwaliteit door reviews
Stuvia-klanten hebben meer dan 700.000 samenvattingen beoordeeld. Zo weet je zeker dat je de beste documenten koopt!
Snel en makkelijk kopen
Je betaalt supersnel en eenmalig met iDeal, creditcard of Stuvia-tegoed voor de samenvatting. Zonder lidmaatschap.
Focus op de essentie
Samenvattingen worden geschreven voor en door anderen. Daarom zijn de samenvattingen altijd betrouwbaar en actueel. Zo kom je snel tot de kern!
Veelgestelde vragen
Wat krijg ik als ik dit document koop?
Je krijgt een PDF, die direct beschikbaar is na je aankoop. Het gekochte document is altijd, overal en oneindig toegankelijk via je profiel.
Tevredenheidsgarantie: hoe werkt dat?
Onze tevredenheidsgarantie zorgt ervoor dat je altijd een studiedocument vindt dat goed bij je past. Je vult een formulier in en onze klantenservice regelt de rest.
Van wie koop ik deze samenvatting?
Stuvia is een marktplaats, je koop dit document dus niet van ons, maar van verkoper Studyclock. Stuvia faciliteert de betaling aan de verkoper.
Zit ik meteen vast aan een abonnement?
Nee, je koopt alleen deze samenvatting voor €12,72. Je zit daarna nergens aan vast.
