Tentamen (uitwerkingen)
NCTI Installer Technician exam 2023 with 100% correct answers
NCTI Installer Technician exam 2023 with 100% correct answers
[Meer zien]Voorbeeld 2 van de 8 pagina's
Voorbeeld 2 van de 8 pagina's
In winkelwagengesponsord bericht van onze partner
Voorbeeld van de inhoud
NCTI MT2 - MT3In what applications is a splice closure used? - correct answer -Splice closures are used to protect optical
fibers and splices against a full range of environmental changes in aerial installations or below ground in
vaults.
When preparing a fiber-optic cable for splicing, what is the purpose of removing approximately 2.5 cm (1
inch) of jacket and any armor that is present, from the end of the cable? - correct answer -To access the
cable's rip cord and to check the cutting depth of the knife or ringing tool
what does water do to the glass core of an optical fiber? - correct answer -Water causes the glass core of
the optical fiber to become opaque, which degrades the signal as it's transported through the fiber.
when preparing a splice closure, what should be done with the fiberglass rod strength member that runs
down the center of loose-tube fiber-optic cable? - correct answer -Trim the strength member back for
convenience, but leave it long enough to be tightly clamped to a strain-relief lug in the closure.
What is the purpose of splice trays inside splice closures? - correct answer -Splice trays are designed to
provide protection for mechanical splices, fusion splice protectors, and optical splitters as well as
provide storage for the required fiber slack.
How should the buffer tubes be secured in the closure? - correct answer -The buffer tubes should be
secured with tie wraps to allow slight movement without pulling or stressing the optical fibers.
How are optical splices secured in a splice tray? - correct answer -Retaining clips hold optical splices in
place in a splice tray.
What is the purpose of buffer tubes in fiber-optic cable? - correct answer -Buffer tubes protect and
separate the optical fiber in smaller bundles.
, When splicing fiber-optic cable, why is it a good safety practice to clean off fiber strippers and other
hand tools after each use? - correct answer -To prevent the accidental transfer of fiber debris or fiber
chips onto clean hands.
Where would you expect to install a mid-entry splice in a fiber-optic cable network? - correct answer -A
location where a select number of optical fibers need to be spliced, and the remaining buffer tubes and
fibers remain untouched.
Which type of fusion splicer is ideal for fiber-to-the-x (FTTx) splicing? - correct answer -The fixed V-
groove splicer.
What are some prerequisites before performing a fusion splice of optical fibers? - correct answer -A
controlled environment such as a splicing van, trailer, or tent and a stable work surface that is large
enough to accommodate the fusion splicer, tools, and the splice closure.
When would a mid-entry splice in a fiber-optic network be used? - correct answer -In a self-healing ring
network that requires only two fibers to feed an optical fiber drop.
What is required of mechanical splices used for acceptance testing? - correct answer -A mechanical
splice used for acceptance testing should be simple to use and reusable.
Why are Velcro straps preferred over standard plastic tie wraps when bundling pigtails for storage in a
splice panel? - correct answer -Because Velcro straps are removable and can hold the pigtails together
without placing undue strain on the optical fibers.
When preparing fiber-optic cable for connection to a patch panel, how much buffer tube and fiber slack
should be provided? - correct answer -Leave enough slack in the buffer tubes to allow the splice trays to
reach the splicing equipment and enough fiber slack to store on individual trays for later additions,
moves, and changes.
If tight-buffered distribution fiber-optic cable is installed between the master splice panel in an optical
entrance enclosure (OEE) and a rack-mounted fiber-optic distribution panel, where in the facility must
the distribution panel be located? - correct answer -The distribution panel can be located anywhere in
the facility since the distribution cable complies with indoor code requirements for riser or plenum
installations.
Voordelen van het kopen van samenvattingen bij Stuvia op een rij:
Verzekerd van kwaliteit door reviews
Stuvia-klanten hebben meer dan 700.000 samenvattingen beoordeeld. Zo weet je zeker dat je de beste documenten koopt!
Snel en makkelijk kopen
Je betaalt supersnel en eenmalig met iDeal, creditcard of Stuvia-tegoed voor de samenvatting. Zonder lidmaatschap.
Focus op de essentie
Samenvattingen worden geschreven voor en door anderen. Daarom zijn de samenvattingen altijd betrouwbaar en actueel. Zo kom je snel tot de kern!
Veelgestelde vragen
Wat krijg ik als ik dit document koop?
Je krijgt een PDF, die direct beschikbaar is na je aankoop. Het gekochte document is altijd, overal en oneindig toegankelijk via je profiel.
Tevredenheidsgarantie: hoe werkt dat?
Onze tevredenheidsgarantie zorgt ervoor dat je altijd een studiedocument vindt dat goed bij je past. Je vult een formulier in en onze klantenservice regelt de rest.
Van wie koop ik deze samenvatting?
Stuvia is een marktplaats, je koop dit document dus niet van ons, maar van verkoper JUICYGRADES. Stuvia faciliteert de betaling aan de verkoper.
Zit ik meteen vast aan een abonnement?
Nee, je koopt alleen deze samenvatting voor €14,86. Je zit daarna nergens aan vast.
Is Stuvia te vertrouwen?
4,6 sterren op Google & Trustpilot (+1000 reviews)
Afgelopen 30 dagen zijn er 82871 samenvattingen verkocht
Opgericht in 2010, al 14 jaar dé plek om samenvattingen te kopen