NCCER

Amsterdam University College (AUC)

Hier vind je de beste samenvattingen om te slagen voor NCCER. Er zijn o.a. samenvattingen, aantekeningen en oefenvragen beschikbaar.

Pagina 2 van de 15 resultaten

Sorteer op

NCCER MILLWRIGHT PRACTICE EXAM  2 QUESTIONS AND ANSWERS
  • NCCER MILLWRIGHT PRACTICE EXAM 2 QUESTIONS AND ANSWERS

  • Tentamen (uitwerkingen) • 9 pagina's • 2024
  • NCCER MILLWRIGHT PRACTICE EXAM 2 QUESTIONS AND ANSWERS unusual - CORRECT ANSWER-If the seal was not properly aligned or there is excessive wear in some bearing or shaft,_______ wear tracks will be the indicator sharpened brass putty knife - CORRECT ANSWER-For removing hard to remove gasket materials found on sealing surfaces, ______ is recommended Conducted on the job - CORRECT ANSWER-Apprenticeship training is_______ distance - CORRECT ANSWER-Charting alignment on a graph requires...
    (0)
  • €15,02
  • + meer info
TEST EXAM FOR NCCER QUESTIONS  AND ANSWERS
  • TEST EXAM FOR NCCER QUESTIONS AND ANSWERS

  • Tentamen (uitwerkingen) • 6 pagina's • 2024
  • TEST EXAM FOR NCCER QUESTIONS AND ANSWERS Hine list, or line table, select the piping specifications - CORRECT ANSWER- What is a wraparound? - CORRECT ANSWER-a tool to lay a straight line around pipe What is. plum? - CORRECT ANSWER-refers to a vertical alignment level, refers to horizontal alignment What are pins used for? - CORRECT ANSWER-align bolt holes when connecting flanges What is a flange spreader used for? - CORRECT ANSWER-to open flanges What does NPT mean? - CORRECT ...
    (0)
  • €13,08
  • + meer info
NCCER Module 1 Exam Review  Questions and Answers Latest Verified
  • NCCER Module 1 Exam Review Questions and Answers Latest Verified

  • Tentamen (uitwerkingen) • 5 pagina's • 2024
  • NCCER Module 1 Exam Review Questions and Answers Latest Verified The person primarily responsible for your safety is ___________. - CORRECT ANSWER-yourself The color commonly used for informational signs is ____________. - CORRECT ANSWER-blue The SDS for any chemical used at a job site must be available ___________. - CORRECT ANSWER-at the job site Companies with strong safety cultures usually have lower __________. - CORRECT ANSWER-turnover Which of these is a true statement...
    (0)
  • €13,57
  • + meer info
NCCER Final Test Exam Questions and  Answers Latest 2024/2025
  • NCCER Final Test Exam Questions and Answers Latest 2024/2025

  • Tentamen (uitwerkingen) • 7 pagina's • 2024
  • NCCER Final Test Exam Questions and Answers Latest 2024/2025 Which of the following BEST describes where the type and size of overcurrent protection is found? - CORRECT ANSWER-Floor plans Electrical charges are measured in: - CORRECT ANSWER-coulombs When installing cables smaller than 4/0 in a cable tray, the allowable cable fill area must NOT be less than - CORRECT ANSWER-cross-sectional areas What is the purpose of a lockout tag-out system? - CORRECT ANSWER-to prevent unexpecte...
    (0)
  • €14,05
  • + meer info
NCCER Pipe Fitters Test Exam  Questions and Answers 100% Verified
  • NCCER Pipe Fitters Test Exam Questions and Answers 100% Verified

  • Tentamen (uitwerkingen) • 8 pagina's • 2024
  • NCCER Pipe Fitters Test Exam Questions and Answers 100% Verified Convert 1/4 to its decimal equivalent. - CORRECT ANSWER-0.25 Piping that is field-routed to a pump must be supported? - CORRECT ANSWER Independently What is used when lighting a cutting torch? - CORRECT ANSWER-Striker Where is specific information needed to install piping and associated items found? - CORRECT ANSWER-Standards and Specifications Damaged and broken tools should be - CORRECT ANSWER-Taken out of service ...
    (0)
  • €14,54
  • + meer info