WMGT 101-22A Exam 3
AFI 10-245, Antiterrorism - correct answer ✔CE shall: have at least 1
engineer at each base must complete Security Eng AT Planning & Design
Course, review, document, and track construction projects AT compliance,
provide vulnerability assessment protection option program (VAPO) analysis
for all critical facilities and off-base leases, and work with the Base
Antiterrorism Officer
Antiterrorism Requirement Planning - correct answer ✔1. UFC 4-020-01
2. Is only the minimum standard required?
3. Yes: construction standoff distance available?
No: UFC 4-020-02 and support manuals
4. If standoff distance is available, apply UFC 4-010-01 and support manuals
Design Basis Threat (DBT) - correct answer ✔Baseline threat used in the
design of protective measures
Initial DBT - correct answer ✔Based on planning team, local intel and
Geographic Combatant Command (COCOM) Theater-Wide threat
assessments
Modify Initial DBT - correct answer ✔Local threat assessments
Level of Protection - correct answer ✔The degree to which an asset is
protected, defines the amount of damage a facility or asset can sustain during
an attack
,LOP: Very low - correct answer ✔Progressive collapse is unlikely, but space
in and around damaged area will be unusable and onset of structural collapse
occurs. Glazing is likely to be propelled into the building and cause serious
injuries. Doors may be propelled into rooms, presenting serious hazards.
LOP: Low - correct answer ✔Building will not be economically repairable and
space in and around damaged area will not be usable, but progressive
collapse will not occur. Glazing will fracture and may come out of the frame,
but does not present a significant injury hazard. Doors may fail but present
minimal hazards.
LOP: Medium - correct answer ✔Minor damage, space in and around
damaged area can be used and will be fully functional after cleanup and
repairs. Glazing will fracture but remain in the frame. Doors may stay in
frames but will not be reusable.
LOP: High - correct answer ✔Minimal to no damage with no permanent
definitions. Glazing will not break. Doors will be reusable.
UFC 4-010-01 - correct answer ✔DoD minimum antiterrorism standards for
buildings. Intent is to reduce mass casualties, minimize collateral damage to
nearby facilities, and facilitate future upgrades and increases FPCON.
UFC 4-020-01 - correct answer ✔DoD Security Engineering Facility Planning
Manual. Acts as a starting point for Garrison Antiterrorism and a quantitative
risk-based model. Uses scoring model to evaluate asset value (0-1.0), threat
likelihood (0-1.0), and use of minimum AT standards (<0.5). Includes cost
data and helps establish a DBT and required LOP.
AT/FP misconceptions - correct answer ✔1. Bollards, fences, curbs, and
barriers are and adequate substitution for standoff
2. Existing roads must be moved away from existing buildings
, 3. All building require standoff
Mandatory design standards - correct answer ✔Standard 1: Standoff
distance
Standard 6: Progressive collapse
Standard 10: Glazing
Standard 16: Air Intakes
Minimum standoff distance - correct answer ✔Smallest permissible standoff
distance for new and existing construction, regardless of analysis or
hardening of the building. Not used for master planning or programming.
Conventional construction standoff distance - correct answer ✔Standoff
distance at which conventional construction may be used for buildings.
Applies for wall types/parameters in Table 2-3. Windows and doors are
designed separately.
Master planning standoff distance - correct answer ✔Based on basic facility
types and an economical blast resistant window construction (UFC 2-100-01
Installation Master Planning)
Main AT/FP Design Strategies - correct answer ✔1. Prevent building
collapse
2. Minimize flying debris
3. Provide effective building layout
4. Limit airborne contamination via HVAC design
5. Provide mass notification
AFI 10-245, Antiterrorism - correct answer ✔CE shall: have at least 1
engineer at each base must complete Security Eng AT Planning & Design
Course, review, document, and track construction projects AT compliance,
provide vulnerability assessment protection option program (VAPO) analysis
for all critical facilities and off-base leases, and work with the Base
Antiterrorism Officer
Antiterrorism Requirement Planning - correct answer ✔1. UFC 4-020-01
2. Is only the minimum standard required?
3. Yes: construction standoff distance available?
No: UFC 4-020-02 and support manuals
4. If standoff distance is available, apply UFC 4-010-01 and support manuals
Design Basis Threat (DBT) - correct answer ✔Baseline threat used in the
design of protective measures
Initial DBT - correct answer ✔Based on planning team, local intel and
Geographic Combatant Command (COCOM) Theater-Wide threat
assessments
Modify Initial DBT - correct answer ✔Local threat assessments
Level of Protection - correct answer ✔The degree to which an asset is
protected, defines the amount of damage a facility or asset can sustain during
an attack
,LOP: Very low - correct answer ✔Progressive collapse is unlikely, but space
in and around damaged area will be unusable and onset of structural collapse
occurs. Glazing is likely to be propelled into the building and cause serious
injuries. Doors may be propelled into rooms, presenting serious hazards.
LOP: Low - correct answer ✔Building will not be economically repairable and
space in and around damaged area will not be usable, but progressive
collapse will not occur. Glazing will fracture and may come out of the frame,
but does not present a significant injury hazard. Doors may fail but present
minimal hazards.
LOP: Medium - correct answer ✔Minor damage, space in and around
damaged area can be used and will be fully functional after cleanup and
repairs. Glazing will fracture but remain in the frame. Doors may stay in
frames but will not be reusable.
LOP: High - correct answer ✔Minimal to no damage with no permanent
definitions. Glazing will not break. Doors will be reusable.
UFC 4-010-01 - correct answer ✔DoD minimum antiterrorism standards for
buildings. Intent is to reduce mass casualties, minimize collateral damage to
nearby facilities, and facilitate future upgrades and increases FPCON.
UFC 4-020-01 - correct answer ✔DoD Security Engineering Facility Planning
Manual. Acts as a starting point for Garrison Antiterrorism and a quantitative
risk-based model. Uses scoring model to evaluate asset value (0-1.0), threat
likelihood (0-1.0), and use of minimum AT standards (<0.5). Includes cost
data and helps establish a DBT and required LOP.
AT/FP misconceptions - correct answer ✔1. Bollards, fences, curbs, and
barriers are and adequate substitution for standoff
2. Existing roads must be moved away from existing buildings
, 3. All building require standoff
Mandatory design standards - correct answer ✔Standard 1: Standoff
distance
Standard 6: Progressive collapse
Standard 10: Glazing
Standard 16: Air Intakes
Minimum standoff distance - correct answer ✔Smallest permissible standoff
distance for new and existing construction, regardless of analysis or
hardening of the building. Not used for master planning or programming.
Conventional construction standoff distance - correct answer ✔Standoff
distance at which conventional construction may be used for buildings.
Applies for wall types/parameters in Table 2-3. Windows and doors are
designed separately.
Master planning standoff distance - correct answer ✔Based on basic facility
types and an economical blast resistant window construction (UFC 2-100-01
Installation Master Planning)
Main AT/FP Design Strategies - correct answer ✔1. Prevent building
collapse
2. Minimize flying debris
3. Provide effective building layout
4. Limit airborne contamination via HVAC design
5. Provide mass notification
