100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
logo-home
Previously searched by you
Previously searched by you
logo
SOS Mechanic Certification- Brakes questions and answers already graded A+ 2024/2025 R241,30   Add to cart
Quickly navigate to
Preview
  2.  
  3. MICHIGAN STATE BRAKES
  4.  
  5. MICHIGAN STATE BRAKES

Exam (elaborations)

SOS Mechanic Certification- Brakes questions and answers already graded A+ 2024/2025
 12 views  0 purchase
  • Course
  • MICHIGAN STATE BRAKES
  • Institution
  • MICHIGAN STATE BRAKES

SOS Mechanic Certification- Brakes questions and answers already graded A+ 2024/2025

Preview 2 out of 6  pages

Document information

  • May 31, 2024
  • 6
  • 2023/2024
  • Exam (elaborations)
  • Questions & answers

Subjects

  • michigan state brakes
  • most 1995 newer vehicles use which of the follow
  • which of the following describes the proper way to
  • the key input for the abs control module comes fro

Written for

  • MICHIGAN STATE BRAKES
  • MICHIGAN STATE BRAKES

Seller

avatar-seller
Ashley96

Reviews received

Content preview

SOS Mechanic Certification- Brakes

Most 1995 & newer vehicles use which of the following types of wheels bearings on non-drive
wheel? - ANSSealed non-serviceable

to test a vacuum power brake booster in the vehicle, you should pump the brake pedal at least 4
times, hold the brake pedal depressed, and start the engine. the brake pedal should: - ANSdrop
slightly and remain firm

You are installing a set of brake shoe linings that are not the same length. Traditionally, the
primary shoe lining is: - ANSSmaller and goes towards the front of the car.

A cracked or torn vacuum diaphragm in a brake power booster would most likely cause: - ANSa
hard pedal feel requiring very high pedal effort to stop

A mechanic finds gear lube inside both rear brake drums on a rear wheel drive vehicle. What is
the most likely cause of this problem? - ANSA plugged axle

Which of the following incorrect service procedures will cause brake lock-up? - ANSmaster
cylinder push rod adjusted too long

Which of the following describes the proper way to depressurized an ABS system? - ANSPump
the brake pedal at least 25 times (or more, depending on the manufacturer's recommendation)
with the ignition off.

The rear brakes are dragging after having new linings installed and the drums machined. the
most likely cause is the: - ANStechnician use the parking brake to adjust shoes and the cable is
stuck

When turning brake drums: - ANSuse a dampening strap to reduce chatter

Which of the following is NOT a necessary drum brake measurement? - ANSrun-out

On a 3-channel system, which wheels are on the same circuit? - ANSboth rear wheels

One way to test an ABS wheel speed signal is to use _____ on your digital multimeter. - ANSAC
volts

The key input for the ABS control module comes from the: - ANSwheel speed sensors

ABS speed sensor and sensor rings: - ANSshould not be hammered or tapped on and should
always be replaced as a matched set

, Flexible brake hoses should be replaced: - ANSwhen dampness is evident on the hose

Which of the following should be used to check for rotor thickness variation: - ANSMicrometer

After rebuilding a master cylinder, the rod between the master cylinder and booster should be: -
ANSadjusted properly

Upon inspecting brake fluid condition, the technician observes the diaphragm in the master
cylinder cup is swollen. Which of the following is the most likely cause? - ANSsilicone fluid
added to the system

When inspecting brake fluid levels, a technician observes low fluid levels. which of the following
should be done first? - ANSInspect disc brake pads for excessive wear

Which of the following is true about most properly functioning anti-lock brake systems? -
ANSThe brakes may lock up at speeds less than 10 miles per hour

Which of the following is true about bleeding brake lines on most ABS equipped vehicles? -
ANSMost ABS brake lines can be bled like a conventional (non-ABS) system. However, caution
must be taken because of the extreme pressure.

Most anti-lock brake systems require the removal of the pressure modulator fuse when: - ANSa
"spaced-saver" spare tire is being used and mismatched tires are being installed

What does a load sensing proportioning valve do? - ANSIt increases the hydraulic pressure
during braking at the rear wheel cylinders when the vehicle is loaded

The brakes of a car squeal each time they are applied, which of the following is the LEAST likely
source of the noise? - ANSGlazed brake pads

Which of the following is a true statement about proportioning valves? - ANSThey provide better
braking balance during hard stops

A properly functioning load sensing proportioning valve will: - ANScause an increase in the
hydraulic pressure during braking at the rear wheel cylinders when the vehicle is loaded.

Why don't disc brake system usually need adjustment? - ANSA certain amount of pressure is
maintained by the metering valve

The front brakes of a car equipped with disc brakes in the front and drum brakes in the rear,
grab quickly as light pressure is applied to the brake pedal, which of the following could be the
cause of the problem? - ANSDefective metering valve

The benefits of buying summaries with Stuvia:

Guaranteed quality through customer reviews

Guaranteed quality through customer reviews

Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.

Quick and easy check-out

Quick and easy check-out

You can quickly pay through EFT, credit card or Stuvia-credit for the summaries. There is no membership needed.

Focus on what matters

Focus on what matters

Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!

Frequently asked questions

What do I get when I buy this document?

You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.

Satisfaction guarantee: how does it work?

Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.

Who am I buying this summary from?

Stuvia is a marketplace, so you are not buying this document from us, but from seller Ashley96. Stuvia facilitates payment to the seller.

Will I be stuck with a subscription?

No, you only buy this summary for R241,30. You're not tied to anything after your purchase.

Can Stuvia be trusted?

4.6 stars on Google & Trustpilot (+1000 reviews)

62890 documents were sold in the last 30 days

Founded in 2010, the go-to place to buy summaries for 14 years now

Start selling
R241,30
  • (0)
  Buy now