1.To measure the strength of a welded joint what mechanical test would you prescribe?
a) A transverse weld tension test
b) A charpy test.
c) A CTOD test.
d) An all weld metal tension test. e) A side bend test. - ANSWERa) A transverse weld tension test
2. Select the cutting process that w...
CWB CORRECT QUESTIONS &
ANSWERS 100% CORRECT!!
1.To measure the strength of a welded joint what mechanical test would you
prescribe?
a) A transverse weld tension test
b) A charpy test.
c) A CTOD test.
d) An all weld metal tension test. e) A side bend test. - ANSWERa) A transverse
weld tension test
2. Select the cutting process that would provide the narrowest heat affected zone
when cutting 12.5 mm (0.5 in) thick carbon steel.
a) Oxy-acetylene cutting.
b) Air-carbon arc cutting.
c) Oxy-propane cutting.
d) Plasma arc cutting.
e) Laser beam cutting - ANSWERe) Laser beam cutting
3. Which of the following refers to a welder test where a pipe assembly is placed
vertically and the joint welded in the horizontal position without rotating the
assembly?
a) 1G
b) 2G
c) 3G
d) 5G
e) 6G - ANSWERb) 2G
4. Which of the following imperfections is normally considered as unacceptable
regardless of size or location?
a) Porosity.
b) Crack.
c) Inadequate penetration.
d) Lamination.
e) Burn-through. - ANSWERb) Crack.
5. Select the correct penetrameter thickness for 2% sensitivity when radiographing a
weldment 1 .25 inches in thickness.
a) 0.012 in.
b) 0.015 in.
c) 0.025 in
d) 0.030 in. - ANSWERc) 0.025 in
6. Which of the following statements concerning porosity is true?
a) Porosity cannot be trapped within a weld.
b) Porosity moves up through later passes and will show only in a final pass.
c) Porosity is restricted to the centre line of a weld.
,d) Porosity can result from faulty welder technique.
e) Porosity can be dissipated by an appropriate heat treatment. - ANSWERd)
Porosity can result from faulty welder technique.
7. An irregular, dense white spot is seen on the radiograph of a weld. Assuming it
was caused by the welding process used, which one of the processes below would
be responsible?
a) SMAW process.
b) GTAW process.
c) GMAW process.
d) ST process.
e) ESW process. - ANSWERb) GTAW process.
8. Which of the following operations is known to result in the emission of ionizing
radiation at levels dangerous to human health?
A) shield metal arc welding.
B) Plasma arc welding.
C) Operation of high voltage portable generator sets.
d) Radiographic inspection.
e) Electroslag and electrogas welding. - ANSWERd) Radiographic inspection.
9. The ultrasonic transducer is pressed against the plate of a welded joint. The
sound travels
longitudinally through the plate to the opposite side. The signal seen on the UT
screen that comes from this opposite side of the plate:
a) Is the initial pulse signal.
b) Is the back reflection signal.
c) Is the front reflection signal.
d) Must be equal in amplitude to any defect signal.
e) Cannot be used for establishing the thickness of the material under test. -
ANSWERb) Is the back reflection signal.
11. Which of the following is a stainless steel electrode?
a) E4918-1
b) E4918-A1
c) E4818
d) E308-16
e) E4111 - ANSWERd) E308-16
12. Reverse polarity refers to the use of a:
a) AC power source, electrode +
b) DC power source, electrode+
c) AC power source, electrode-
d) DC power source, electrode- - ANSWERb) DC power source, electrode+
13. Which welding process(es) can result in metallic inclusions in the weld?
a) SMAW.
b) FCAW.
c) GMAW.
d) GTAW
, e) SAW - ANSWERd) GTAW
14. In producing a drawing for a scale of 1:50, what would be the distance
represented by a distance on the drawing of 6 em?
a) 12 em.
b) 30 em.
c) 50 em.
d) 240 em.
e) 300 em. - ANSWERe) 300 em.
15. As a general rule, weld discontinuities detected by ultrasonic testing are
accepted or rejected on the basis of:
a) Vertical linearity.
b) Time base analysis.
c) Horizontal response data.
d) Noise to signal ratio.
e) Signal amplitude. - ANSWERe) Signal amplitude.
16. An advantage of an AC welding circuit is:
a) It is best used with large electrodes on thin materials.
b) It is best used with small electrodes on thin sections.
c) It helps to eliminate arc blow.
d) It minimizes internal undercut. - ANSWERc) It helps to eliminate arc blow.
17. The resistance of steel to failure by brittle fracture is commonly assessed by
conducting a:
a) Rockwell C hardness test.
b) Tensile test.
c) Chemical analysis.
d) Hydrogen embrittlement test.
e) Notched bar impact test. - ANSWERe) Notched bar impact test.
18. Which one of the following SMAW electrodes is restricted to horizontal and flat
position welding?
a) EXX18
b) E4916
c) EXX10
d) E4924
e) E4914 - ANSWERd) E4924
19. The mechanical test used to determine the ability of a material to resist failure by
brittle fracture requires the use of:
a) A tensile test specimen.
b) A bend test specimen.
c) A compression test specimen.
d) An impact test specimen .
e) A spectrographic test. - ANSWERd) An impact test specimen .
20. Select the electrode that would be best suited for welding high sulphur steels in
the flat position:
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through EFT, credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying this summary from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller papersbyjol. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy this summary for R260,04. You're not tied to anything after your purchase.
